Thinning Vallejo matte varnish

Supported by (Turn Off)

This topic has 8 replies, 9 voices, and was last updated 7 years, 4 months ago by johankimigo.

Viewing 9 posts - 1 through 9 (of 9 total)

Author

Posts
December 9, 2018 at 9:08 pm #1312171

lorddgort
159xp

1

I prefer to use a brush on matte varnish to protect my miniatures. I recently saw a tutorial where a painter thinned a brush on matte varnish with water. I was surprised as I believe I contaminated my Vallejo varnish one time with water (a dish that hadn’t been properly dried) and I think it caused the varnish to “fog”. Parts of the mini turned white in the creases. Does anyone out there thin their varnish? With water or with something else, like a flow improver. Any advice would be greatly appreciated.

December 9, 2018 at 9:18 pm #1312173

somegeezer
18480xp

0

I’m the same with mine, even if I really don’t like slopping it on without thinning it. Would love to hear some success stories.

December 9, 2018 at 9:36 pm #1312175

torros
23839xp

0

I used to use the Vallejo Matt varnish but never found it gave a particularly Matt finish.

I don’t see why it couldn’t be thinned a little but I think you need to make sure your water was very very clean

December 10, 2018 at 6:44 am #1312231

brucelea
7906xp

0

I thin my Vallejo paints and varnishes with both water and their thinner. I also spray it and brush it. The most important thing to do is let everything stabilise at the same temperature, or ghosting can happen. I try not to go any varnish spraying when it’s too cold as that seems to be when it happens most.

December 10, 2018 at 7:31 am #1312234

horati0nosebl0wer
20563xp

0

I haven’t had any ghosting with the Vallejo matte varnish when brushed on. I have had that with aerosol use of Testor’s Dullcote. I only use the Vallejo gloss regularly when I want to fill in small areas or over metals that I’m going to paint over and scratch battle damage.

In any case a little thinning shouldn’t be a problem. Just be sure not to drown your work in the stuff.

December 10, 2018 at 9:11 am #1312259

amachan
25791xp

0

I thin my Vallejo varnishes with some of their airbrush thinner, but then I also apply it with an airbrush. However with their polyurethane matt varnish I always had problems fogging up, no matter what I did. Their acrylic varnishes work perfectly fine for me.

December 26, 2018 at 6:23 pm #1317512

hooferinsane
120xp

0

I thin Vallejo matte varnish (always with clean water) with no problems. Have had some disasters with aerosols though (GW brands) so won’t use them anymore

December 26, 2018 at 7:28 pm #1317524

commodorerob
11087xp

0

Although I have started to use Army Painter anti shine recently. I always applied Vallejo Matt after thinnuth it with clean water and never had any issues with it at all.

December 31, 2018 at 5:10 pm #1318390

johankimigo
20xp

0

I’m the same with mine, even if I really don’t like slopping it on without thinning it. Would love to hear some success stories.

https://ovo.fyi/chaturbate/

https://ovo.fyi/xnxx/

https://ovo.fyi/tubegalore/
Author

Posts

Viewing 9 posts - 1 through 9 (of 9 total)

You must be logged in to reply to this topic.